Altronix AL1002ULADAJ NAC Power Extender - 24VDC @ 10 amp w/Large Enclosure

Altronix AL1002ULADA

NAC Power Extender - 24VDC @ 10 amp w/Large Enclosure


Model AL1002ULADA is an extremely cost effective 10 amp voltageregulated remote power supply/battery charger. It may be connected toany 24 volt Fire Alarm Control Panel (FACP). Primary applicationsinclude Notification Appliance Circuit (NAC such as strobes and horns)expansion support to meet ADA requirements. It also provides auxiliarypower to support system accessories. The unit delivers regulated andfiltered 24 volt power to Class B or Class A NAC loop circuits.Additionally, a separate 1.0A auxiliary output with reset for four(4)-wire smoke detectors is available. The 10 amp rated supply currentcan be divided between the four (4) outputs for powering NAC devices.Each output is rated at 2.5 amp max., and can be independentlyprogrammed for Steady, Temporal Code 3 or Strobe Synchronization. Alloutputs may be programmed for Input to Output Follower Mode (outputwill follow input. i.e. March Time Input, March Time Output). Anindividual output of 4 amp is achieved by paralleling 2 outputs. Innon-alarm condition independent loop supervision for Class A and/orClass B FACP NAC circuits is provided. In the event of a loop troublethe FACP will be notified via the steered input (input 1 or input 2).In addition, there are common trouble output terminals (NC, C, NO)which are used to indicate general loop/system trouble. A commontrouble input is provided for optional NC (normally closed) devices toreport trouble to the FACP. Two (2) FACP signaling outputs can beemployed and directed to control supervision and power delivery to anycombination of the four (4) outputs. The unit also features LoopOutput trouble memory indication to help identify troublesome sporaticproblems. Model is available in a larger enclosure AL1002ULADAJ

Features/Specifications
Power Supply/Charger:
24VDC output.
10 amp max total alarm current.
115VAC 60Hz., 4.4 amp.
Short circuit and thermal overload protection.
Built-in charger for sealed lead acid or gel type battery backup.
Maximum charge current .7 amp.
Zero voltage drop upon transfer to battery backup.
AC input and DC output LED indicators.
AC fail supervision (form "C" contact rated @ 1 amp 28VDC).
Low battery and battery presence supervision (form "C" contact rated @ 1 amp 28VDC).
Lifetime Warranty.

Logic Board:
Class 2 Rated power limited outputs.
Two (2) Class A or two (2) Class B FACP inputs.
Two (2) NC dry contact trigger inputs.
Two (2) Class A or four (4) Class B Indicating Circuits.
Two (2) Class B outputs may be paralleled for more power on an indicating circuit.
One (1) Aux. Power Output @ 1 amp supply current (w/Battery Back Up).
Signal Circuit Trouble Memory - facilitates quickly locating intermittent system trouble and eliminates costly and
unnecessary service calls. LEDs indicate a prior fault (short, open, ground) has occured on one or
more signaling circuit outputs.
2-wire horn/strobe Sync mode allows audible notification appliances (horns) to be silenced while visual notification
appliances (strobes) continue to operate.
Horn/Strobe sync protocols include: Wheelock , Gentex , System Sensor , Faraday, Amseco.
Temporal Code 3 Mode.
Steady Mode.
Input to Output Follower Mode (maintains synchronization of notification appliance circuits).
March Time.
Compatible with 24VDC or 12VDC fire panels.
Common Trouble inputs and outputs.
Ground fault detection.
Lifetime Warranty.

Enclosure
Accommodates up to two (2) 12VDC/12AH batteries.
Dimensions: 15.5H x 12W x 4.5D.
1/2" and 3/4" combination knockouts.

Data Sheet